Procedure On Grandfather Clock Regulation
The most important thing in a watch is its movement which mainly controls timekeeping, the hour strike, and the chime. The pendulums, as well as the, weighs, are also vital gadgets in the grandfather clock regulation. Usually, the pendulum gives one the ability to control and adjust time therefore if the pendulum is adjusted well, accurate timekeeping can be achieved very easily.
There are usually three weights that are used in providing power to the left weight (hour strike), center weight (time) and the right weight (chime and melody). These weights are very necessary to the operation of the antique watch. Thus they have to be present. The weights are very different from each other, and they should hang adequately to make sure that the operation is okay.
There are specific cables that are used when the weights are hanged when the clock is moving, and it is necessary that you raise them after a week to ensure the watch is in a good working condition. Some hammers are used in hitting some rods which in turn make the chime as well as the strike to produce specific sounds. Controlling the hammers can make the chimes to produce different melodies.
Therefore, a person must be aware of the components of a wristwatch and their corresponding uses so that he/she can be in a position to control and regulate the watch. The wristwatch should be firmly placed on the floor to prevent it from falling over. Therefore, the levers must be adjusted properly to ensure maximum stability as well as proper alignment.
After stabilizing the watch, hanging pendulums is the next thing. Make sure that you hang them well so that they do not fall. Before that, you have to remove the plastic film that protects the pendulum then carefully remove the disk. Make sure that you have followed all the guidelines without any additions or subtractions if you want your watch to work.
Once you finish hanging all the pendulums, this is time to put the weights in place as well. Make sure that you have checked whether they are assembled tightly and in the proper order. To add on that, make sure that the cables have been correctly put in their cable pulleys before you proceed to hang the weights.
If the watch has more features like a moving moon dial, you can set it as well. This can be done by applying some pressure to the front part of the moon dial using your fingers. You then have to rotate the dial clockwise if the moon dial fails to rotate, you can try to set it again after six hours. You should not force the dial as it is supposed to move freely.
The next thing is to set the time, but you should know that only the minute hand is moved. Therefore, do not move the hour hand as you will interfere with it. This is because the hour hand tends to move automatically when the minute hand moves. You should also not move the hands when the wristwatch is striking. You can then start the watch since all the regulation is over.
There are usually three weights that are used in providing power to the left weight (hour strike), center weight (time) and the right weight (chime and melody). These weights are very necessary to the operation of the antique watch. Thus they have to be present. The weights are very different from each other, and they should hang adequately to make sure that the operation is okay.
There are specific cables that are used when the weights are hanged when the clock is moving, and it is necessary that you raise them after a week to ensure the watch is in a good working condition. Some hammers are used in hitting some rods which in turn make the chime as well as the strike to produce specific sounds. Controlling the hammers can make the chimes to produce different melodies.
Therefore, a person must be aware of the components of a wristwatch and their corresponding uses so that he/she can be in a position to control and regulate the watch. The wristwatch should be firmly placed on the floor to prevent it from falling over. Therefore, the levers must be adjusted properly to ensure maximum stability as well as proper alignment.
After stabilizing the watch, hanging pendulums is the next thing. Make sure that you hang them well so that they do not fall. Before that, you have to remove the plastic film that protects the pendulum then carefully remove the disk. Make sure that you have followed all the guidelines without any additions or subtractions if you want your watch to work.
Once you finish hanging all the pendulums, this is time to put the weights in place as well. Make sure that you have checked whether they are assembled tightly and in the proper order. To add on that, make sure that the cables have been correctly put in their cable pulleys before you proceed to hang the weights.
If the watch has more features like a moving moon dial, you can set it as well. This can be done by applying some pressure to the front part of the moon dial using your fingers. You then have to rotate the dial clockwise if the moon dial fails to rotate, you can try to set it again after six hours. You should not force the dial as it is supposed to move freely.
The next thing is to set the time, but you should know that only the minute hand is moved. Therefore, do not move the hour hand as you will interfere with it. This is because the hour hand tends to move automatically when the minute hand moves. You should also not move the hands when the wristwatch is striking. You can then start the watch since all the regulation is over.
About the Author:
When you are searching for information about grandfather clock regulation, visit our web pages today. More details are available at http://www.customtime.net/routine-maintenance now.
Comments
Post a Comment